Decoration requirements for clean operating department
1. Surgical wall
1. Surgical wall
2022
05
23
5. The feeder is damaged
1.Fault condition:
Collide with undershoot
Cause of failure:
1.Fault condition:
Collide with undershoot
Cause of failure:
2022
05
23
Tomorrow we will send another container of goods to Ningbo port, and then send it to our customers by sea. We have successfully applied for all the formalities, and the traffic in Suzhou has returned to normal. As long as we apply in advance, we can normally enter and exit large trucks. Customers who need to order our products can contact us at any time and place orders as soon as possible. The recent sea freight is relatively low, which can save a lot of purchase costs.
2022
05
23
What is the purpose of the clean room test of the clean workshop? Most of the owners are based on the original vision of the purification project to complete the test indicators. Of course, this is the most straightforward goal and method
2022
05
17
LED purification lights can generate continuous negative ions to make the air fresh and clean. Effectively eliminate smoke and odors in the air, while eliminating germs and viruses. LED purification lamp
2022
05
17
Water is the source of life, and today's industrial production is inseparable from water. As a drug to protect human health, the quality of pharmaceutical water is related to the life safety of users
2022
05
17
Pulsating vacuum pressure steam sterilizer is a medical device that extracts vacuum and fills steam into the sterilization chamber alternately for many times (fill saturated steam after the sterilization chamber reaches a certain vacuum degree), and finally reach the set pressure and temperature, so as to realize the sterilization of high temperature and humidity resistant articles. It is used for damp heat sterilization of medical instruments and surgical instruments and drying treatment after
2022
05
17
Shipping is gradually recovering, and we have ushered in the peak of shipments
The Suzhou area was finally lifted this week after a period of lockdown.
The Suzhou area was finally lifted this week after a period of lockdown.
2022
05
17
What is a laminar flow hood used for?
The clean laminar flow hood is an air purification unit that can provide a local high clean environment. It can be flexibly installed above the process points that require high cleanliness. The clean laminar flow hood can be used alone or combined into a strip-shaped clean area.
The clean laminar flow hood is an air purification unit that can provide a local high clean environment. It can be flexibly installed above the process points that require high cleanliness. The clean laminar flow hood can be used alone or combined into a strip-shaped clean area.
2022
05
17
Detection of indoor airflow pattern
1. Layout of measuring points:
The vertical unidirectional flow (laminar flow) clean room shall have one longitudinal section and one transverse section respectively
1. Layout of measuring points:
The vertical unidirectional flow (laminar flow) clean room shall have one longitudinal section and one transverse section respectively
2022
05
17
1、 Filter leak detection
For the high-efficiency filter installed at the end of air supply and exhaust, the scanning method shall be used for filter installation frame and full section leakage detection. There are two scanning methods: leak detector method (photometer method) and particle counter method with a minimum sampling amount of 1l / min. For ultra-high efficiency filter, there are two scanning methods: condensation nodule counter method and laser particle counter method.
For the high-efficiency filter installed at the end of air supply and exhaust, the scanning method shall be used for filter installation frame and full section leakage detection. There are two scanning methods: leak detector method (photometer method) and particle counter method with a minimum sampling amount of 1l / min. For ultra-high efficiency filter, there are two scanning methods: condensation nodule counter method and laser particle counter method.
2022
05
17
1. Jacking
Fault condition:
After the upper punch enters the middle die, the machine stops running
Cause of failure:
Fault condition:
After the upper punch enters the middle die, the machine stops running
Cause of failure:
2022
05
17
no data
Contact Us
Telephone: +86-18241958031/
+86-18913598640
Fax: 86-512-65488640
Email: pharma@sz-pharma.com
Whatsapp/Wechat: 008618241958031
Notice:
We hereby declare that our company's only legal contact is through the the above email, Any other similar suffix is a scammer email.
Address: NO.188 xiangwei road, near junction of xiangwei road and chengyang road (the second floor of south building inside of haiji feiyue) Xiangcheng district, Suzhou city, Jiangsu province, China
no data
Copyright © 2025 Suzhou Pharma Machinery Co., Ltd. | Privacy Policy Sitemap