Powder and granule purification workshop

Powder and granule purification pharmaceutical cleanroom

Purification pharmaceutical cleanroom powder and granule packing machine is a device that quantitatively packs materials into composite membrane materials. It is made by spraying high pressure polyethylene, and the composite film material makes the spraying high...

Text label: Design and construction of powder purification workshop, granule clean workshop decoration manufacturer

Powder and granule purification pharmaceutical cleanroom

Purification workshop powder and granule packing machine is a device that quantitatively packs materials into composite membrane materials. It is made by spraying high-pressure polyethylene. The composite film material makes the sides of the sprayed high-pressure polyethylene stick together, and can be bonded to form a pocket by means of an adjustable temperature heat sealing device; , hopper, material tray, heat sealing device, cutter and control box; the rolled composite film material is stuck on the shaft of the film support, and the film pulling device below makes the composite film material easy to pull out in place, and the composite film material enters The lower shaper is gradually folded in half, and heat-sealed to form a pocket. A certain amount of powder or granule is placed in the outer bag, and then heat-sealed and cut to obtain the finished product; the length of the pocket can be read by a photocell. The cursor can be used to determine, or it can be cut at a fixed length. In order to facilitate the tearing of the pocket, a serrated knife can be used or a small slit can be cut on the edge of the pocket.

The quantitative dispensing of powders and granules mostly adopts container-type metering. Several containers are evenly distributed on the bottom surface of the slightly inclined material tray. The upper opening of the container is flush with the bottom surface of the material tray. The open and closed nylon baffle, when the scraper scrapes the upper mouth of the container, a certain amount of material is contained in the container, and the material tray rotates intermittently under the push of the stepping mechanism. The lower shutter is opened under the action of the overhead, and all the materials in the container will fall down, pass through the former, and enter the pocket formed by the heat sealing of the composite film; The device is closed under the action of the closing pin, so as to continue to accommodate the material. The actual charging amount is generally compensated by adjusting the gap between the scraper and the material tray, but the gap should not be too large to avoid inaccurate measurement, and the gap should not be too large. small, so as not to cause severe wear of the scraper. Zhongjing Global Purification can provide consulting, planning, design, construction, installation, transformation and other supporting services for purification workshops and clean workshops.

Cup-type granule dispenser can be made into various styles, such as heat-sealing devices, some use pairs of L-shaped heat-sealers, vertical sealing and horizontal sealing are completed at one time, and some use strip-type heat-sealing and roller-type heat-sealing devices ; In order to prevent the high temperature from affecting the quality of hot air, some pellet encapsulation machines are equipped with cooling water jackets. Before starting the machine, the upper and lower water pipes of the water jackets should be connected, and tap water should be used for cooling. Confirm that there is cooling water flowing out of the water jacket outlet. Before starting the machine; some pellet packing machines use two film rolls facing each other, instead of one film roll being folded in half on the former, so that multiple pockets can be formed after being heat-sealed by multiple rollers, because each pocket is It is heat-sealed on four sides instead of three, so the appearance is flatter and more beautiful. The powder with a smaller dose in the purification workshop is packed by screw, or a powder dispenser can be used. It is packed in a paper bag formed by three folding, and then transferred into the outer bag. After embossing and tuyere, the powder is packed and packed. packing operation.

In today's world, have risen to an unexpected level of extraction machine. It has gained a lot of popularity and has come up with different kinds of variations in its content.

To receive more professional tips and super quality products for extraction machine, go to our website PHARMA MACHINERY to place your order. Do not wait any longer.

These extraction machine CUSTOM SOLUTION SERVICES are not only useful but also more cost effective than those traditional ones.

SUZHOU PHARMA MACHINERY CO.,LTD. might focus its marketing efforts by highlighting its end product—improved technology and increased profits—not its producing methods.